This is what the PRO'S use to apply their Graphics - Making the job alot easier

The Original Rapid Tac
For fast, easy, quality installation of graphics with no bubbles, even in cold weather.

This environmentally friendly product is great for installing decals and vinyl graphics.
Granted, not all applications call for a "wet" procedure, but we do know that in most applications, forty to sixty percent labor time can be saved by using an application fluid. Sometimes one person can do a job (normally requiring two people to apply dry) in less time if an application fluid like Rapid Tac or new Rapid Tac II is used. (Rapid Tac II bonds faster than Rapid Tac, and is intended for films with a lower tac adhesive than premium vinyl.)

Application fluid cleans without leaving residues. It then helps to "float" the vinyl until it is properly positioned. Best of all Rapid Tac and Rapid Tac II stimulates the adhesive to bond in approximately ninety seconds, even in adverse climates such as extreme hot or cold. It will not cause bubbles so there's no returning to poke holes in your work either. Your customers and your reputation will benefit from higher-quality applications.

STEP 1. Clean surface thoroughly with Rapid Tac/Rapid Tac II and a kitchen paper towel. DO NOT USE OTHER CLEANERS OR SOLVENTS.
(We do recommend Rapid Prep as a pre-cleaner for surfaces that may have been exposed to wax, silicone, or other suspected contaminants)

STEP 2. Spray surface again with Rapid Tac/Rapid Tac II. Peel backing off decal and place on wet surface.

STEP 3. Position decal. Use squeegee to remove fluid, using a good deal of pressure and working from the center out to the edges in all directions.

STEP 4. Wait 2-3 minutes. Saturate paper cover tape, if any, with Rapid Tac/Rapid Tac II, then remove paper tape. Wipe surface with paper towel.


Detailed Use Instructions




Rapid Tac

Bottlel Size and Price

Quantity:




Rapid Tac II
For fast, easy, quality applications with no bubbles or wrinkles, even in cold weather.

New Rapid Tac II will enable you to perform wet applications with a wider variety of film types (Intermediate, Cast, Economy, Calendared, Metallic, Reflective, Polyester, Mylar).

Rapid Tac II will also give you better control, allowing vinyl to bond faster to glass, and in cold weather (down to approximately 25 degrees f.)

Rapid Tac II is not a replacement for the Original Rapid Tac, and may bond too fast with "Premium Cast" films in warmer climates.

STEP 1. Clean surface thoroughly with Rapid Tac/Rapid Tac II and a kitchen paper towel. DO NOT USE OTHER CLEANERS OR SOLVENTS. (We do recommend Rapid Prep as a pre-cleaner for surfaces that may have been exposed to wax, silicone, or other suspected contaminants)

STEP 2. Spray surface again with Rapid Tac/Rapid Tac II. Peel backing off decal and place on wet surface.

STEP 3. Position decal. Use squeegee to remove fluid, using a good deal of pressure and working from the center out to the edges in all directions.

STEP 4. Wait 2-3 minutes. Saturate paper cover tape, if any, with Rapid Tac/Rapid Tac II, then remove paper tape. Wipe surface with paper towel.


Detailed Use Instructions




Rapid TacII

Bottlel Size and Price

Quantity:




Rapid Prep
A Non-hazardous, Non-Flammable pre cleaner.

For cleaning or pre-cleaning, Rapid Prep is a non-hazardous wash solvent that removes wax, grease, oil and silicone. After using Rapid Prep to clean the substrate (sign panels, autos or boats) you can apply paint or vinyl. Rapid Prep is also non- flammable, making it a superior product for sign shops, body shops and trim shops where safety is a big concern. Rapid Prep was formulated by people with hands on experience, with a desire to have a safer more effective pre-cleaner.
This water born product is formulated for the removal of silicones, waxes, oils, road tars and other contaminates from surfaces being prepared for painting or for the application of vinyl graphics. Rapid Prep helps eliminate the problems of fish-eyeing of paints, also will increase the adhesion of vinyl graphics.
Rapid Prep is a safe and economical product that all paint and application shops will benefit from.
Rapid Prep also takes the place of many hazardous petroleum based products currently on the market today.
Rapid Prep is NON-HAZARDOUS, NON-FLAMMABLE AND NON-TOXIC.

How about saving some more labor hours? When removing signs, stripes and graphics Rapid Remover is a guaranteed labor-saving product. Most people in shops are using lacquer thinner, MEK, acetone, paint stripper, grinders, etc., all of which are hazardous products. Start by using a heat lamp tree to soften vinyl and after peeling off vinyl you will have the adhesive to deal with.




Rapid Prep

Bottlel Size and Price

Quantity:




Rapid Clear

The perfect end to a job well done. Rapid Clear cleans and polishes plexiglass, glass, and most polycarbonates. Use Rapid Clear as a final cleaning for your sign work, auto restoration, etc. Non-hazardous and bio-degradable.

Perfect For:

* Household Glass
* Auto GlassAircraft Windows
* Marine Windows
* TV Screens
* Computer Monitors
* Tined Glass
* Eye Wear
* Safety Sheilds
* Cameras
* Optical Equipment




Rapid Clear

Bottlel Size and Price

Quantity:




Rapid Remover
For removing adhesives quickly without damage or mess

This environmentally friendly product is great for removing adhesive glue left over by decals and vinyl graphics. Rapid Remover is a non-toxic, water-soluble that breaks down and removes adhesives in sixty seconds! You spray it on, wait thirty to sixty seconds, and easily wipe it off with a plastic squeegee, with no damage to painted or bare metal surfaces. What may have been a four-hour job (and a messy one at that) can now be done in one and half-hours: an easy, clean and non-damaging removal. Your shop or business will benefit greatly from these products; think of them as tools. Get the right tool for the job!

*
STEP 1. Remove decal with heat lamp or heat gun.
*
STEP 2. Spray glue residue with Rapid Remover and let penetrate for 30-60 seconds.
*
STEP 3. Using a squeegee, scrape to remove glue residue.
*
STEP 4. Spray Rapid Remover on a paper towel and wipe surface clean.
*
STEP 5. Rinse surface with Rapid Remover Application fluid or water. Product is water-soluble.

Detailed Use Instructions



Rapid Remover

Bottlel Size and Price

Quantity:




Cool New Stuff
Hot Rod Cleaning Supplies, This has to be the best and fastest cleaning system for your Hot Rod cleaning needs..
Wally Wags Microfiber Cleaning Cloths are answer to the dreaded chore of keeping your ride clean.If you don't look or buy anything else here, you have to buy this product, I am amazed by this stuff ..Click image to check out the Hotrodworks.net Cleaning Systems.
Cleans so easy and fast, You got to try this product....

You won't find a better deal , these Cleaning Cloths are the Best Price and are the Biggest Sizes you will find...

These cloths are the best... won't scacht yor vinyl, remove the dust and dirty when you prep and absorb the water when appling decals

Also Pay By Phone Order, Mail in, Check or Money order - Print Order Form, Continue to order and select your type of payment on Order Form.These optoins will be there for you to choose.
Contact Woodguy
All artwork, images, and content of the website are property of THE HOT ROD WORKS